Monitors
|
Top Features
| 10” fiberglass/paper composite driver > full, tight bass response for accurate monitoring |
 |
| all-discrete 240-watt internal amplifier > plenty of power to reproduce extended low frequencies |
|
| variable 50-200Hz crossover > compatible with any direct-field monitor system |
|
| subwoofer bypass footswitch > audition how your mixes will sound with and without a subwoofer |
|
| flared rear bass-reflex port > high efficiency, minimal air turbulence |
The M-Audio® SBX10 active subwoofer is designed to give your monitoring system some serious low end. The SBX10 delivers tight, clean bass response down to 20Hz—revealing the extreme low frequencies in your music so you can make accurate mixing decisions. Comprising a 10” fiberglass/paper composite driver, a 240-watt all-discrete internal amplifier, and a variable 50-200Hz crossover, the SBX10 subwoofer delivers unbeatable performance in a compact chassis—great for studios where space is tight. An oversized magnet, high-temperature voice coil, high-density cabinet and a full complement of inputs are just some of the additional components that round out this high-quality design. The unit even includes a bypass footswitch so you can easily judge how mixes will sound with and without a dedicated subwoofer. The SBX10 represents the perfect addition to any studio monitor setup.
Full Features
|
| 10” fiberglass/paper composite cone driver with oversized magnet and high-temperature 2” long-throw voice coil |
|
| 240-watt Class A/B amplifier with all-discrete transistor design |
|
| flared rear bass-reflex port |
|
| variable 50-200Hz crossover |
|
| 20-200Hz low frequency response |
|
| adjustable gain (-30dB to +6dB) |
|
| balanced/unbalanced XLR, balanced/unbalanced 1/4” TRS and RCA inputs |
|
| balanced/unbalanced XLR and balanced/unbalanced 1/4” TRS outputs allow easy setup of 2.1 monitoring systems |
|
| includes subwoofer bypass footswitch |
|
| phase switch (0°/180°) |
|
| over-temperature protection |
|
| vinyl-covered high-density internally braced 3/4” MDF cabinet with 1” front and back baffles |
|
| removable grill |
|
| removable feet |
Specifications
|
| type: |
bass-reflex active powered subwoofer
|
|
| woofer driver: |
10-inch composite (treated paper/fiberglass) cone with high-temperature voice coil and damped rubber surround
|
|
| frequency response: |
20-200Hz (-3dB)
|
|
| crossover: |
HP/LP linked filter sweepable from 50-200Hz; 24dB/octave 4th-order alignment
|
|
| input sensitivity: |
80mV pink noise input produces 100dBA output SPL at one meter with volume control at maximum
|
|
| adjustable gain: |
(-30dB to +6dB)
|
|
| amplifier: |
240 watts average power into 4, discrete transistor design
|
|
| signal-to-noise ratio: |
96dB (A-weighted)
|
|
| THD at rated power, mono mode: |
0.019%
|
|
| inputs: |
two XLR balanced/unbalanced inputs; two TRS balanced/unbalanced inputs; two unbalanced RCA
|
|
| outputs: |
two XLR balanced/unbalanced outputs for satellites; two TRS balanced/unbalanced outputs for satellites
|
|
| controls: |
volume/gain control, phase inverse switch, variable crossover control, subwoofer bypass footswitch jack
|
|
| input impedance: |
20k ohms balanced, 10k ohms unbalanced
|
|
| maximum input level: |
+20dBU
|
|
| protection: |
over temperature, turn-on/off transient, subsonic filter, external mains fuse, DC protection, over current protection
|
|
| indicator: |
power on (blue) or standby/bypass (red)
|
|
| power requirements: |
dual-voltage (selectable by rear-panel switch) for either 100-120V/~50/60Hz or 220-240V/~50/60Hz; powered via detachable grounded IEC cable
|
|
| cabinet: |
vinyl-laminated high-density internally braced 3/4” MDF cabinet with 1” front and back baffles
|
|
| dimensions: |
15.5 in. (h) x 13 in. (w) x 17.25 in. (d); 39.4 cm (h) x 33 cm (w) x 43.8 cm (d)
|
|
| shipping weight: |
54.6 lbs.; 24.75 kg |
|
